电气工程学报 ›› 2023, Vol. 18 ›› Issue (3): 145-153.doi: 10.11985/2023.03.016

• 电机与电器 • 上一篇    下一篇

扫码分享

基于累积误差补偿的永磁同步电机低速插值控制策略*

张冰鑫1(), 刘侃1(), 李跃1, 胡伟1, 黄庆2, 陈泳丹3   

  1. 1.湖南大学机械与运载工程学院 长沙 410082
    2.株洲中车时代电气股份有限公司 株洲 412001
    3.中国北方车辆研究所 北京 100072
  • 收稿日期:2022-08-25 修回日期:2023-03-26 出版日期:2023-09-25 发布日期:2023-10-23
  • 通讯作者: 刘侃,男,1982年生,博士,教授。主要研究方向为轨道交通/新能源车电驱技术、伺服控制等。E-mail:lkan@hnu.edu.cn
  • 作者简介:张冰鑫,男,1997年生,硕士研究生。主要研究方向为永磁同步电机驱动控制技术。E-mail:zhangbingxin@hnu.edu.cn
  • 基金资助:
    * 国家自然科学基金(51877075);湖湘高层次人才聚集工程(S2019RSCXRC0094)

Low Speed Interpolation Control Strategy of Permanent Magnet Synchronous Motor Based on Accumulative Error Compensation

ZHANG Bingxin1(), LIU Kan1(), LI Yue1, HU Wei1, HUANG Qing2, CHEN Yongdan3   

  1. 1. College of Mechanical and Vehicle Engineering, Hunan University, Changsha 410082
    2. Zhuzhou CRRC Times Electric Co., Ltd., Zhuzhou 412001
    3. China North Vehicle Research Institute, Beijing 100072
  • Received:2022-08-25 Revised:2023-03-26 Online:2023-09-25 Published:2023-10-23

摘要:

基于观测器法的增量式编码器脉冲信号插值控制是一种常用的低速控制方案,但是在每个位置脉冲内,其会产生累计误差,进而对矢量控制系统的精度和稳定性造成影响。为降低误差累积造成的负面影响,提出一种基于累积误差补偿的插值控制算法。该方法利用前一个位置脉冲的累计插值误差,在当前位置脉冲的插值过程中引入误差补偿项,在每个采样周期内抵消误差累积,从而抑制了具有同向积累特性的误差累积现象。最后,在一台750 W永磁同步伺服电机对所提方法进行了性能测试,结果显示其相较于传统基于观测器法的插值控制策略具有更高的控制精度和抗外部扰动性能。

关键词: 永磁同步电机, 误差补偿, 滑模观测器, 锁相环, 位置插值

Abstract:

The observer based interpolation control for incremental encoder pulse signal is a common low speed control scheme. However, it will produce an accumulative error within each position pulse, which will affect the accuracy and stability of vector control system. In order to mitigate the negative effect caused by error accumulation, an interpolation control algorithm based on accumulative error compensation is proposed. In the proposed method, the accumulative interpolation error of the last position pulse is used as the compensation term added into the interpolation process of current position pulse for the cancellation of accumulative error in each sampling period. Thus, the phenomenon of accumulative error being monotonic increasing is suppressed afterwards. Finally, the performance of the proposed method is tested on a 750 W permanent magnet synchronous servo motor, and the results show that it has higher control accuracy and better anti-interference to external disturbances than the traditional observer-based interpolation control strategy.

Key words: Permanent magnet synchronous motor, error compensation, sliding mode observer, phase-locked loop, position interpolation

中图分类号: