Spiral Vector Modeling of Brushless Doubly-fed Induction Machines with Short-circuited Rotor Windings

doi:10.23919/CJEE.2021.000023

电气工程学报 ›› 2021, Vol. 7 ›› Issue (3): 29-41.doi: 10.23919/CJEE.2021.000023

扫码分享

收稿日期:2021-04-13 修回日期:2021-05-04 接受日期:2021-05-31 发布日期:2021-09-17

Spiral Vector Modeling of Brushless Doubly-fed Induction Machines with Short-circuited Rotor Windings

Peng Han^1,*, Ming Cheng², Zhiwei Zhang³, Peng Peng⁴

1. Ansys, Inc., San Jose, CA 95134, USA;
2. School of Electrical Engineering, Southeast University, Nanjing 210096, China;
3. Department of ECE, The Ohio State University, Columbus, OH 43210, USA;
4. Milwaukee Electric Tool Corporation, Milwaukee, WI 53005, USA

Received:2021-04-13 Revised:2021-05-04 Accepted:2021-05-31 Published:2021-09-17
Contact: * E-mail: peng.han@uky.edu
About author:Peng Han received the B.Sc. and Ph.D. degrees in Electrical Engineering from the School of Electrical Engineering, Southeast University, Nanjing, China, in 2012 and 2017, respectively.From November 2014 to November 2015, he was a joint Ph.D. student funded by China Scholarship Council with the Department of Energy Technology, Aalborg University, Aalborg, Denmark, where he focused on the brushless doubly-fed machines for wind energy conversion and high power drive. He was a Postdoctoral Researcher with the Center for High Performance Power Electronics (CHPPE), Department of Electrical and Computer Engineering, The Ohio State University, and later the SPARK Laboratory, Department of Electrical and Computer Engineering, University of Kentucky. He is currently with Ansys, Inc. as an Application Engineer. His current research interests include electric machines, power electronics and renewable energy.
Ming Cheng received the B.Sc. and M.Sc. degrees from the department of Electrical Engineering, Southeast University, Nanjing, China, in 1982 and 1987, respectively, and the Ph.D. degree from the Department of Electrical and Electronic Engineering, University of Hong Kong, Hong Kong, China, in 2001, all in Electrical Engineering.Since 1987, he has been with Southeast University, where he is currently a Chief Professor at the School of Electrical Engineering and the Director of the Research Center for Wind Power Generation. From January to April 2011, he was a Visiting Professor with the Wisconsin Electric Machine and Power Electronics Consortium (WEMPEC), University of Wisconsin, Madison, WI, USA. His teaching and research interests include electrical machines, motor drives for EV, and renewable energy generation. He has authored or co-authored more than 400 technical papers and 5 books, and is the holder of 130 patents in these areas. Prof. Cheng is a Fellow of the Institution of Engineering and Technology. He has served as the Chair and an Organizing Committee Member for many international conferences. He is a distinguished Lecturer of the IEEE Industry Application Society in 2015/2016.
Zhiwei Zhang received the Ph.D. degree in Electrical Engineering from the Huazhong University of Science and Technology, Wuhan, China, in 2016. He is currently a Visiting Scholar with the Department of Electrical and Computer Engineering, The Ohio State University, Columbus, OH, USA. His current research interests include design and analysis of advanced electric machines, variable-speed ac drives, transportation electrification, and renewable energy conversion systems.
Peng Peng received the Ph.D. degree in Electrical and Computer Engineering from The Ohio State University, Columbus, OH, USA, in 2020. Since 2021, he has been a Motor Control Engineer with Milwaukee Electric Tool Corporation developing control algorithms for high-speed motors. His research interests include electric machines, magnetic materials, control theory, and power electronics.

摘要/Abstract

Abstract: A unified spiral vector model is presented that can be used to assist the finite element method-based performance analysis of brushless doubly-fed induction machines with various short-circuited rotor windings. Specifically, magnet-free brushless doubly-fed induction machines working in doubly-fed or singly-fed synchronous mode are investigated. A dynamic model in spiral vector notation is developed, based on which the torque-angle and power-angle characteristics are derived. It is shown that the investigated brushless machines are equivalent to a traditional non-salient-pole synchronous machine with brushes. By introducing a conversion factor, they can also be analyzed with methods similar to the conventional phasor theory. A comparison is made between the brushless doubly-fed induction machine and non-salient-pole wound-field synchronous machine with brushes, revealing that the performance of the brushless machine degrades faster when the laminated core is saturated. A scaled-down prototype is tested to validate the effectiveness of the theoretical analysis.

Key words: AC machine, brushless machine, modeling, performance evaluation, synchronous machine

. [J]. 电气工程学报, 2021, 7(3): 29-41.

Peng Han, Ming Cheng, Zhiwei Zhang, Peng Peng. Spiral Vector Modeling of Brushless Doubly-fed Induction Machines with Short-circuited Rotor Windings[J]. Journal of Electrical Engineering, 2021, 7(3): 29-41.

参考文献

[1] M Cheng, Y Zhu.The state of the art of wind energy conversion systems and technologies: A review.Energy Convers. Manage., 2014, 88: 332-347.
[2] L Xu, Y Liu, X Wen.Comparison study of singly-fed electric machine with doubly-fed machine for EV/HEV applications. in Proc. Int. Conf. Electr. Mach. Syst. (ICEMS), Beijing, China, 20-23 Aug. 2011.
[3] R A McMahon, P C Roberts, X Wang, et al. Performance of BDFM as generator and motor.IEE Proc.-Electr. Power Appl., 2006, 153(2): 289-299.
[4] P Han, M Cheng, Z Chen.Dual-electrical-port control of cascaded doubly-fed induction machine for EV/HEV applications.IEEE Trans. Ind. Appl., 2017, 53(2): 1390-1398.
[5] R S Rebeiro, A M Knight.Two-converters-based synchronous operation and control of a brushless doubly fed reluctance machine.IEEE Trans. Mag., 2018, 54(11): 8107205.
[6] Z Zhang.Robust stator-excited brushless synchronous machine: An attractive permanent magnet-free option. in Proc. Int. Conf. Electr. Mach. Syst. (ICEMS), Harbin, China, 11-14 Aug. 2019.
[7] Z Zhang.A brushless doubly fed machine with separated field and armature windings in dual stators. in Proc. Int. Electr. Mach. Drives Conf. (IEMDC), San Diego, CA, USA, 12-15 May, 2019.
[8] P Han, M Cheng, S Ademi, et al.Brushless doubly-fed machines: Opportunities and challenges.Ch. J. Electr. Eng., 2018. 4(2): 1-17.
[9] M Ruviaro, F Runcos, N Sadowski, et al.Analysis and test results of a brushless doubly fed induction machine with rotary transformer.IEEE Tran. Ind. Electron. 2011, 59(6): 2670-2677.
[10] F Xiong, X Wang.Design of a low-harmonic-content wound rotor for the brushless doubly fed generator.IEEE Trans. Energy Convers., 2014, 29(1): 158-168.
[11] F Zhang, S Yu, X Wang, et al.Research of a novel brushless doubly-fed generator with hybrid rotor.IEEE Trans. Appl. Supercond., 2016, 26(7): 0608205.
[12] R Li, A Wallace, R Spée.Dynamic modeling, simulation and stability analysis of brushless doubly-fed machines.IEEE Trans. Energy Convers., 1991, 6(3): 445-452.
[13] R Li, A K Wallace, R Spée.Two-axis model development of cage rotor brushless doubly-fed machines.IEEE Trans. Energy Convers., 1991, 6(3): 453-460.
[14] R Li, A K Wallace, G C Alexander.Dynamic simulation of brushless doubly-fed machines.IEEE Trans. Energy Convers., 1991, 6(3): 445-452.
[15] J Poza, E Oarbide, D Roye, et al.Stability analysis of a BDFM under open-loop voltage control. in Proc. European Conference on Power Electronics and Applications, Dresden, Germany, Sep. 2005: 1-10.
[16] I Sarasola, J Poza, E Oyarbide, et al.Stability analysis of a brushless doubly-fed machine under closed loop scalar current control. in Proc. Industrial Electronics Conference (IECON), Paris, France, Nov. 2006: 1527-1532.
[17] P C Roberts, T J Flack, J M Maciejowski, et al.Two stabilizing control strategies for the brushless doubly-fed machine (BDFM). in Proc. International Power Electronics, Machines and Drives Conference (IPEMDC), Venue, UK, Jun. 2002: 341-346.
[18] D Zhou, R Spee, G C Alexander.Experimental evaluation of a rotor flux oriented control algorithm for brushless doubly-fed machines.IEEE Trans. Power Electron., 1997, 12(1): 72-78.
[19] M S Boger, A K Wallace, R Spee, et al.General pole number model of the cage-rotor brushless doubly-fed machine.IEEE Trans. Ind. Appl., 1995, 31(5): 1022-1028.
[20] P C Roberts, T Long, R A McMahon, et al. Dynamic modelling of the brushless doubly fed machine.IET Proc.-Electr. Power Appl., 2013, 7(7): 544-556.
[21] J Poza, E Oyarbide, D Roye, et al.Unified reference frame d-q model of the brushless doubly-fed machine.IET Proc.-Electr. Power Appl., 2006, 153(5): 726-734.
[22] J Poza, E Oyarbide, I Sarasola, et al.Vector control design and experimental evaluation for the brushless doubly fed machine.IET Proc.-Electr. Power Appl., 2009, 3(4): 247-256.
[23] S Shao, E Abdi, F Barati, et al.Stator-flux-oriented vector control for brushless doubly fed induction generator.IEEE Trans. Ind. Electron., 2009, 56(10): 4220-4228.
[24] F Barati, S Shao, E Abdi, et al.Generalized vector model for the brushless doubly-fed machine with a nested-loop rotor.IEEE Trans. Ind. Electron., 2011, 58(6): 2313-2321.
[25] W R Brassfield, R Spee, T G Habetler.Direct torque control for brushless doubly-fed machines.IEEE Trans. Ind. Appl., 1996, 32(5): 4474360.
[26] I Sarasola, J Poza, M A Rodriguez, et al.Direct torque control design and experimental evaluation for the brushless doubly fed machine.Energy Convers. and Manage., 2011, 52(2): 1226-1234.
[27] A Zhang, X Wang, W Jia, et al.Indirect stator-quantities control for the brushless doubly fed induction machine.IEEE Trans. Power Electron., 2014, 29(3): 1392-1401.
[28] R Zhao, A Zhang, Y Ma, et al.The dynamic control of reactive power for the brushless doubly fed induction machine with indirect stator-quantities control scheme.IEEE Trans. Power Electron., 2015, 30(9): 5046-5057.
[29] H Gorginpour, B Jandaghi, H Oraee, et al.A novel rotor configuration for brushless doubly-fed induction generators.IET Electr. Power Appl., 2013, 7(2): 106-115.
[30] M Cheng, P Han, W Hua.General airgap field modulation theory for electrical machines.IEEE Trans. Ind. Electron., 2017, 64(8): 6063-6074.
[31] M Cheng, P Han, Y Du, et al.A tutorial on general air-gap field modulation theory for electric machines.IEEE J. Emerg. Sel. Top. Power Electron., DOI: 10.1109/JESTPE. 2021.3055224.
[32] S Yamamura.Spiral vector theory of AC circuits and machine, 1^st ed. Oxford: Clarendon, 1992.
[33] D W Novotny, T A Lipo.Complex vector analysis of induction machines. Vector control and dynamics of ac drives, 1st ed. New York: Oxford University Press Inc., 1996.
[34] P Han, M Cheng, X Wei, et al.Modeling and performance analysis of a dual-stator brushless doubly fed induction machine based on spiral vector theory.IEEE Trans. Ind. Appl., 2016, 52(2): 1380-1389.
[35] P Han, M Cheng, X Wei, et al.Steady-state characteristics of the dual-stator brushless doubly fed induction generator.IEEE Trans. Ind. Electron., 2018, 65(1): 200-210.

Spiral Vector Modeling of Brushless Doubly-fed Induction Machines with Short-circuited Rotor Windings

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价